Product

T50 --- 50W CO2 LASER TUBE

Minimum Order : 1 , Pieces

SPT-T50 Main Parameters

Model SPT- T50
Length 1000mm
Pipe Diameter 50±1mm
Wavelength 9.6~10.6um
Output Power   Stable Value 60W
Max Output Power 70W
Triggering   Voltage 20KV
Working Voltage 12KV
Working  Current 20mA
Max Working   Current 25mA
Cooling Water-cooling 15-25℃, 4L/min
Impulse   Frequency 100% to 5KHZ
Spot Diameter 4±1mm

CO2 laser (laser tube) Installation instructions

1. Make sure the electrodes are connected correctly;

2. The cooling water pipe installation. When installing water pipe, please make sure the cooling water inlet must follow from the positive to negative, and down into the water, and the interface is not leaking. Before starting the laser tube must store enough water in the water cooling pipes and no air bubbles before use (must check every time before start laser tube). If the laser tube is mounted vertically, please ensure that no air bubbles at the top of the laser tube. It will cause thermal shock when it runs with air bubbles in the water pipe, which is easy to damage your laser tube.

3. To maintain the good performance of laser tube, keep the cooling water temperature between 20-25 °C. The instability of cooling water's temperature will influence laser tube output power.

4. When installing the laser tube, please try to ensure the 1/4 point in laser tube length is on laser tube holder, this can help your laser tube get best working performance. And leave enough space between the laser tube positive end (it has high voltage electricity) and any metal surface of your laser machine. If the space is not big enough, it will cause ignition between high voltage power used to trigger the laser tube and the metal surface of laser machine, and thus lead to laser tube damage and even breakdown of major electronic components on your laser machine.

5. Recommend laser machine consumers to put automatic checkout device into your laser tube water cooling system to prevent laser tube stoppage due to overheating failure caused by lack of water when laser tube is working, please consult your laser machine supplier for details.



CO2 Laser Tube Common Working Problems

Weak output laser power

1. Check if any scratches or dirt on laser tube output lens and the laser tube put on laser tube support at right point (Marked as"suggested support point"on SPT laser tube).

2. Check the output current of laser machine, service voltage, cooling water temperature, cleanness and rate of water flow.

3. Check the cleanness of focus lens and the reflectors on your laser machine, check whether the lens and reflective mirrors get hot or the laser beam is not well aligned.

High voltage electric discharge ignition

1. Check if any sundries around the high voltage electricity joint or the laser tube is too close to metal part of laser machine;

2. Too humid indoor environment will also cause electric conduction phenomena. Please pay attention to phenomenon of condensation water in laser tube when using water chiller in summer days.

3. Check if any contact defective or open circuit in laser power internal high-voltage connections.

Laser tube broken or the laser tube ends fallen off

1. Cooling water temperature must be 15 to 25 degrees. The cooling water can be frozen in cold area to cause laser tube broken from inside, so don’t leave any water within the laser tube when temperature is under 0 degree.

2. The tube must run under water protection device is on. (To test the tube lights or not with water supplied or not)

3. Check the silicon water pipe is folded or pressed by something.

4. Check if any bubbles in the laser tube.

5. Check whether the cooling water flow rate is normal and the water is circled from low to high.

If conditions 1-5 are normal, it is laser tube quality problem.

Laser tube breakdown caused by wrong operations of 1~5 conditions is not covered by warranty policy.


SPT laser is established in Dongguan, Guangdong province, China. Its main factory is located in Jiangsu, where is close to Shanghai. All workshops are dust-free, which contain over 100 workers. Main office is located in Dongguan city, which is in charge of the management of whole company as well as sales and shipping. SPT Laser is professional manufacturer of glass co2 laser tube, laser lens and laser mirror, also supplies co2 laser power supply, RF laser tube maintenance service, etc to help customers save their cost with higher efficiency. SPT laser is dedicated to supply the best quality product and perfect laser solutions with same cost for customers.

Recently, we’ve launched our FEEL TEK series product--- dynamic laser marking system. It is designed to get much larger scale working area at lower cost compare to other normal laser marking machine, 3D laser marking system is available as well. We are aiming to help our customers get perfect working performance with lower cost and higher machine stability. All Dynamic laser solutions are customized based on your actual needs and budget with high quality imported optical parts and electronics.

 

Our products are mainly:

1, Main components for co2 laser cutting and engraving machines;

2. Dynamic co2 and fiber laser marking solutions and 3D laser marking system;

3. Agent brand new RF laser tube and maintenance service for used RF laser tube.


Related Search

Send Inquiry